Domain specific | DR commands | File Listing | Netcon Commands | SSP Daemons
The tables below provide a summary of all E10K commands
Reset and reboot hung domain |
cb_reset |
upgrade the prom |
cb_prom |
Create new domain or recreate old domain |
domain_create |
Display or remove domain history |
domain_history |
Remove an existin domain |
domain_remove -d <domain name> |
Rename an existing domain |
domain_rename |
Display domain status |
domain_status |
Send a command to EDD daemon |
edd_cmd_x -e Display event monitoring -x [start|stop|rc] Stop/start or reread config |
Display or control fan power and speed |
fan |
Display, change and set system clock freqencies |
sys_clock |
Configure SSP IP or control boards |
ssp_config [cb] Configure control board setup [float] Configure floating SSP IP address |
Deconfigure the SSP |
ssp_unconfig |
scantool and interconnect auto config |
autoconfig |
Read or write board ID values |
board_id |
Remote emulation debugger, used to debug record stops |
redx |
Configure and boot a domain |
bringup -f Force execution -A[on|off] bringup domain (on = boot domain) -l[level] level of hpost testing -X <file> specify blacklist file |
determine whether the domain is up |
check_host |
Display system information |
hostinfo |
Control and sequence POST through JTAG |
hpost |
Network console GUI |
netcontool |
Control Power |
power |
Send commands from SSP to domain |
sigbcmd |
Display, set and change system clock frequencies |
sys_clock |
Display or change system ID in SSP IDProm |
sys_id -d Display all fields -k <key> Change the system ID -s <serial number> Change the serial number -h <host> Change the host ID -x Display the serial number in HEX |
panic a hung domain resulting in a reboot |
hostint |
Reset a hung host |
hostreset |
Display SSP failover status |
showfailover |
Set failover to on or off |
setfailover [on|off] |
failover SSP |
setfailover force |
switch active control board |
setfailover -t cb force |
Reset a hung host |
hostreset |
DR GUI |
drview |
Network console server |
netcon_server |
DR shell |
dr |
initiate a DR attach operation |
init_attach |
complete a DR attach operation |
complete_attach |
abort a DR attach operation |
abort_attach |
start a memory drain |
drain [sb] System board (0-15) |
initiate a DR detach operation |
init_detach |
complete a DR detach operation |
complete_detach |
abort a DR detach operation |
abort_detach |
initiate auto-configuration sequence, reconfigure devices |
reconfig |
Blacklist File |
/var/opt/SUNWssp/etc/<platform_name>/blacklist |
eeprom image |
/var/opt/SUNWssp/etc/<platform_name>/<domain_name>/eeprom.image |
boot processor ID |
/var/opt/SUNWssp/etc/<platform_name>/<domain_name>/bootproc |
event configuration file |
/var/opt/SUNWssp/etc/<platform_name>/<domain_name>/edd.erc |
domain messages files |
/var/opt/SUNWssp/adm/<domain_name>/messages /var/opt/SUNWssp/adm/messages |
STOP-A a domain |
~# |
Display all netcon sessions |
~? |
swiatch between private LAN and JTAG |
~= |
Private netcon session mode |
~* |
Locked write mode |
~& |
Unlocked write mode |
~@ |
Read-only mode |
~^ |
exit current netcon session |
~. |
cbs | The control board server (cbs) provides central access to the E10K control board for client programs running on the SSP |
edd | Event detector daemon uploads event detection scripts to control boards. When one of these scripts detects an event, edd executes response action script |
netcon_server | connection point for all netcon clients |
fad | File access daemon provides file access services to SSP clients that need to monitor, read and write to the SSP configuration files |
machine_server | This daemon services the TCP port registration requests from netcon_server and ensures that error messages are routed to the proper message file. |
obp_helper | During execution obp_helper provides services to OBP such as nvram simulation, IDprom simulation and time of day |
fod | Fail-over daemon monitors SSP to control board comms |
datasyncd | This daemon keeps files in sync between main and spare SSP |